washing machine overflow

How To Deal With A Washing Machine Overflow?

Washing machine overflow is obviously one of those worst-case scenarios you hope will never happen in your home. If this happens, it was likely caused by a problem with the water inlet valve or level switch. Water all over the floor may seem like a fun slip-n-slide to your kids, but you know well that is an expensive problem to fix. Several people who see their washing machine overflow may panic and call a service professional, thinking that the situation is critical. This is the right thing but before you call the professionals, look at the causes of washer overload and try to prevent them.

What causes the washing machine overflow?

When a washing machine overflows, the main reason is that the water flow inside the drum either goes above the normal level or reaches the top of the door glass. You have to turn off the washing machine and half fill it with water. After that, you have to see if the water s still running or has stopped. If water hasn’t stopped, there have a problem with either the water level switch or the inlet valve. Remember that they need to be cleaned out so lint won’t build up inside, also causing your drains to overflow.

How to deal when an overflow occurs?

  • Firstly you have to switch off the power supply to the washer at the circuit breaker or fuse box. Remember, absolutely don’t try to press the “Cancel” button on the washer’s control panel since this can worsen the overflow by activating the drain cycle.
  • Secondly, you have to remove any items near or around the flooded area and dry them as quickly as possible.
  • After that wipe up the floodwater, and dry the room with fans and dehumidifiers.
  • The fourth step is to take away the clothes from the washer and wring them out over a sink in the kitchen or laundry room.
  • You have to control the washer hoses for damage.
  • Pull carefully the washer away from the wall and look for drippings or leaks.
  • Check the machine’s instruction manual to learn what to do when the cycle stops prematurely.

Steps to prevent a washing machine overflow

  • Periodically clean standpipe and drains

Of course, the lint, dirt, and debris can clog the washing machine’s drainage system. Several washing machines can eliminate the blocked drains with a simple lint. So check the washing machine manual for insights on what the manufacturer suggests to clean the pipe and drain clear of clogs.

  • Try to don’t overfill the washing machine

Everyone thinks that it is tempting to shove as much laundry as you can possibly fit. Fewer loads of laundry you have fewer loads to do, right? But remember that, it’s not a time saver because your clothes typically don’t get as clean. And also it can result in other problems. If you put too much in your washing machine can actually cause unnecessary stress on the machine, and ultimately risk an overflowing problem.

  • It is recommended to install standpipe at the appropriate height

This height is always dependent on the specific make and model of your appliance. Some machines need the standpipe to be at a height of 36 inches or higher. If it is not, the washing machine can cause overflow or backflow.

  • It is very important to use the detergent

High-efficiency washing machines require a particular detergent. These detergents help to reduce the amount of suds and bubbles that are produced and decrease the risk of overflows.

  • Don’t forget to register the machine with its manufacturer

One of the most important things to do is registering your appliance with its manufacturer keeps you informed of recalls that could potentially cause problems.

Washing machine overflow Tips

Tip1: Turn off the power

Overflowing water is very dangerous when met with electricity. If you press the washer’s cancel button is not enough to avoid the risk. Furthermore, the outlet plug may have been exposed to water. So the best do is to cut the power off at the circuit breaker or fuse box until you’ve cleared the area of standing water and understand if it’s safe to have electrical near the problem area. Another thing is that, if you turn the power off and the overflow continues occurring, it could be an indication that there is a defective water inlet valve. So you have to replace the valve and it is typically an easy, inexpensive fix.

Tip2: Check the water pressure

You have to know that low water pressure can cause water overflow. This may occur when the water inlet valve needs at least 20psi to properly turn off. If it doesn’t meet this minimum, the valve may fail to properly shut off and allows water to leak.

Tip3: Make sure that the drain hose is fully functional

Drainage from the washing machine can sometimes fill the drain hose with unwanted materials and backs up the water’s escape route. You have to check it and ensure it has free flow. Furthermore, check to make sure the drain hose is free of cracks or worn areas.

WHY US?

CPR24 Restoration is a full-service mould remediation company. What it means is that we offer the full scale of solutions needed for complete removal and prevention of mould. From identifying the cause of mould to fixing any design flaws or tubing associated with it to repairing or replacing the affected areas, and the prevention of further mould by removal and sealing to rigorous testing to detect any traces of new mould, we strive to be a leader in the mould solutions industry.

By following our team tips, you easily will remove mould in areas such as bathroom walls and floors, however, if you have a significant mould issue, please call CPR24 Restoration.